1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

Gas Gauge for 18' whaler outrage
Key-z	#1  Posted on 03/28/08 - 4:40 AM
Member Posts: 102 Comments: 5 Joined: 08/14/06	Does anyone know how many wholes are on the gas tank to accommodate a mechanical gas gauge? Thank you! Key-z
Jeff	#2  Posted on 03/28/08 - 4:51 AM
Member Posts: 1987 Comments: 34 Joined: 04/02/05	Are you asking if there is more than one spot already in the tank to install a gauge? Edited by Jeff on 03/28/08 - 4:55 AM 1993 23' Walkaround Whaler Drive
Key-z	#3  Posted on 03/29/08 - 2:27 PM
Member Posts: 102 Comments: 5 Joined: 08/14/06	NO, not an additional hole for the gas gauge. I want to go back to the original mecahnical gas gauge with the see through deck plate in the floor as oppose to an electrical gas gauge on the console. I feell the mechaical works better. I had a new tank built by Florida Marine in October of 2006. The mechanical gauge got pitched with the old tank when the new tank was fabricated. I didn't care much at the time because I was going to install a new gauge on the console. What a mistake. It worked a couple , three times and then worked on and off for about two months until it doesn't work at all. Make sense? Key-z
Phil T	#4  Posted on 03/29/08 - 2:55 PM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	Take a look at the wire connections on the sender on top of the tank. From the symptoms you report (interminant) You could have a loose connection. Check the ground connection too.. If everything is okay on the sender, check the wires on the back of the gauge. I have had the opposite experience with gas gauges. 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT
Key-z	#5  Posted on 04/01/08 - 1:05 PM
Member Posts: 102 Comments: 5 Joined: 08/14/06	Thanks CBO I'll check on all you mention this weekend when I trek down to the Keys. Hope your suggestions resolves my issue with the gas gauge because I can't seem to find a mechanical gauge. I'll let you know the results just as soon as I test. Kind Regards, Key-z
kamie	#6  Posted on 04/01/08 - 1:58 PM
Member Personal Page Project Albums Posts: 2975 Comments: 3 Joined: 11/04/05	http://www.e-components.net/ Contact e-components and see if they have a gauge that will fit.
pglein	#7  Posted on 04/02/08 - 1:21 PM
Member Posts: 15 Comments: 0 Joined: 03/18/08	The new West Marine catalog has a gauge that at least LOOKS exactly like the OEM one. No idea if it's actually the same or not, but it's clearly the same concept.
Key-z	#8  Posted on 04/21/08 - 5:59 PM
Member Posts: 102 Comments: 5 Joined: 08/14/06	Thanks guys, for all the good advice. I did have a mechanic look at it and he found a wire loose. I took it out this past weekend and it worked for a little while and then conked out. I'll check and tighten the wires one more time.If that doesn't fix the problem, then I'll be forced to purchase a mechanical gauge from e-components and a clear deck plate from twin cities marine. I'll also check the gauge West Marine carries. Thanks again, Key-z