1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

17’ outrage kicker mount ?
Chale	#1  Posted on 02/26/21 - 8:50 PM
Member Posts: 5 Comments: 0 Joined: 01/17/21	Does anyone have a good kicker mount recommendation for 1991 outrage 17’ ? Boat currently has a 2-stroke Yamaha 115 weighing 337 lbs that takes up transom. Was planning to mount the kicker on starboard side and it’s to be used for the chance main motor konks out when at sea. Was thinking a 5-6 hp would suffice. Thanks in advance for any info.
Phil T	#2  Posted on 02/27/21 - 9:17 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	Chale - Welcome to WC. Please specify which Outrage 17 model you have. 1990-1995 Outrage 17 I 1996-1999 Outrage 17 II My answer depends on your answer. 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT
Chale	#3  Posted on 02/27/21 - 9:39 AM
Member Posts: 5 Comments: 0 Joined: 01/17/21	It’s a 1991 outrage 17’ (1990-1995).
Phil T	#4  Posted on 02/27/21 - 1:26 PM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	I would be hesitant to add a kicker to the Outrage 17 I. This model does not handle much more than 375 lbs of transom weight well. My 1991 model had a 405 lb F115 and it was very tender in seas. I am in the midst of repowering my 1992 with an E-TEC 90 for the weight. Simulate the added weight of a kicker and bracket by adding weight to the splashwell. 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT
Chale	#5  Posted on 02/27/21 - 7:18 PM
Member Posts: 5 Comments: 0 Joined: 01/17/21	Seems like a 2-stroke kicker would get me within the weight limits. I will try to add weight incrementally onto the rear seat and see when it’s noticeable.
Phil T	#6  Posted on 02/28/21 - 8:08 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	A good test is to add the simulated weight to the splashwell, launch the boat with a full fuel tank and run out to some 2' waves (not swells). Come off plane and stop. Now back down into a wave. Note - A functional bilge pump is required for this test. 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT
Chale	#7  Posted on 07/05/21 - 8:53 PM
Member Posts: 5 Comments: 0 Joined: 01/17/21	Mr. Phil, Have you replaced the original fuel tank on your 17’ outrage ? If you did, can you tell me a place you ordered it from ? I think it would be wise for me to get this replaced in the near future maybe this winter. Thanks in advance for any information.
Phil T	#8  Posted on 07/06/21 - 9:28 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	I have not. For now I will run off a portable tank installed in the baitwell location. I plan to replace hoses and pressure test the tank this winter. The original tank is still available from Florida Marine Tank in North Carolina. Due to the significant shipping cost, it is recommended to owners west of the Mississippi have a local metal fabricator duplicate the tank. If you have basic DIY skills, you can derig the console, slide forward, lift the tank cover, remove the hoses and ground and pull the tank. We can help you through this. The pre-covid price to estimate price for a tank is $8.00 per gallon of capacity. A local fabricator can use the existing for a new tank. The sender is available from www.e-components.net Edited by Phil T on 07/06/21 - 9:36 AM 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT
Chale	#9  Posted on 07/11/21 - 7:54 PM
Member Posts: 5 Comments: 0 Joined: 01/17/21	I think a tank can be purchased from Atlantic Coast Welding. They seem to have the skematics for tank dimensions on file. I will have to confirm with Florida marine tanks to confirm for sure or pull the existing tank and measure it. Might tackle this project after fishing season. Did some trolling a few weeks ago and seemed to burn a lot of fuel. I suspect my boat with a 115 V4 2-stroke and 34 gallon tank would likely get me 70 or so miles of running (2 miles per gallon). Does that seem accurate ?
Phil T	#10  Posted on 07/12/21 - 6:34 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	FMT will not release drawings. You will need to remove the tank to get the actual measurements. i would check with Atlantic on their pricing and backlog. Most firms are running out 3-9 months. 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT