1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

Seat Clamp Dimensions for 11' Classic
SHdansurfs	#1  Posted on 01/01/21 - 8:05 AM
Member Posts: 4 Comments: 0 Joined: 12/22/20	I have a 1976 11' Classic with tiller steering. My boat is currently missing the port and starboard seat clamps. Can anyone send me the dimensions/specs/template of the wood so that I can build them myself and install them? If this information is already on WC, please point me to it. Thanks in advance. Edited by SHdansurfs on 01/04/21 - 11:32 AM
Joe Kriz	#2  Posted on 01/11/21 - 5:29 PM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	We have the drawings for the Sport 13' Not sure if the seat clamps are different in size for the 11' https://www.whalercentral.com/downloa...?cat_id=13
SHdansurfs	#3  Posted on 01/12/21 - 10:55 AM
Member Posts: 4 Comments: 0 Joined: 12/22/20	Joe...Thanks, that helps. But, before I get out my saw and drill, I may wait and see if an 11' BW owner might measure and post the dimensions. Thanks again, and appreciate your work on this site.
biggiefl	#4  Posted on 01/12/21 - 11:20 AM
Member Posts: 890 Comments: 4 Joined: 05/08/06	I will look as I have them in my garage. Mine is a sport model so I will just measure the passenger side as you do not have the console. Yours should be two of the same as it is just to hold down the twart. You might want to customize it for height if you want to put the tank under it etc. 24 Whalers so far....
SHdansurfs	#5  Posted on 01/12/21 - 2:03 PM
Member Posts: 4 Comments: 0 Joined: 12/22/20	Thanks so much in advance. I live in downtown Tampa, so if your boat is nearby, I'd be happier to take the measurements if it's easier...
Joe Kriz	#6  Posted on 01/12/21 - 4:28 PM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	Once we find out what length the 11' model is, we can compare them to the 13' model. 13' length of the seat clamp is 54 inches and the height is 4 inches. see the attachment below. Also in our Downloads section for the rest of the drawings for the 13' Sport model. Joe Kriz attached the following image: [31.7Kb]
Phil T	#7  Posted on 01/13/21 - 6:09 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	From Nick Space for the twart is about 11". Rail is 35.5" long. 3" tall and little over 3/4" wide. Phil T attached the following image: [64.05Kb] 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT
biggiefl	#8  Posted on 01/13/21 - 10:16 AM
Member Posts: 890 Comments: 4 Joined: 05/08/06	Thanks Phil. The cut out is evenly spaced from front to rear with 2 screws on each side screwing it to the gunwale. 24 Whalers so far....
SHdansurfs	#9  Posted on 01/13/21 - 11:42 AM
Member Posts: 4 Comments: 0 Joined: 12/22/20	Phil, Nick...Thanks a ton. This is a huge help. Time to get started on a new project...
YankeeDollar	#10  Posted on 11/11/21 - 12:23 PM
Member Posts: 1 Comments: 0 Joined: 11/11/21	Would anyone happen to have the seat dimensions for the classic 11' w/ tiller? My mahogany seat was split in half in a hurricane, and I've unfortunately lost my notes with measurements on it.