View Thread
Before Posting, Please Read Our Posting Guidelines Below.

1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

 Print Thread
1985 Montauk trailer question
PFSquan
#1 Print Post
Posted on 08/10/18 - 9:20 AM
Member

Posts: 13
Comments: 0
Joined: 04/04/06

I recently bought a Sea Lion S 17-1700 for my 1985 Montauk. This is a bunk trailer with a single roller at the bow. It was originally adjusted to fit although I wasn't happy with the height because I have to tilt my 90 Yamaha slightly or the skeg will touch the ground. I plan to raise the bunk brackets as high as I can to gain a few inches for the skeg. However, the port bunk shifted so that needs attention, too, but in the process should the bunks be flat or is there a recommended angle to best support the hull?. Each carpeted bunk is 5 3/4 " wide. Also, is there a standard measurement where that bunk needs to be to properly support the hull? Thanks for any suggestions. I don't trailer other than to go to and from the water once a season so I appreciate any input.

Peter

 
wrangler
#2 Print Post
Posted on 08/11/18 - 3:30 AM
Member

Posts: 264
Comments: 0
Joined: 03/14/08

1979 Montauk, Yamaha 90 4 stroke.

Continental trailer- My 8 foot bunks are angled to match the V of the hull and are located approx. 15" either side from the drain plug. They extend from 2" past the transom to about the center of the console . You want the motor tilted when trailering to avoid contact with the road and at the ramp to avoid hitting the rampover angle and the bottom when launching and retrieving. The bunks need to contact the hull the full width of the bunk and they will be angled to make this contact. Use tie down straps to hold the boat to the trailer. They are Required by law in Florida and prevent hull and transom damage.

I also have a keel roller at each crossover to avoid any hull damage if I hit a crossover when retrieving.

 
PFSquan
#3 Print Post
Posted on 08/12/18 - 7:41 AM
Member

Posts: 13
Comments: 0
Joined: 04/04/06

Thank you very much for that. Peter

 
Joe Kriz
#4 Print Post
Posted on 08/12/18 - 2:10 PM
User Avatar
Site Owner
Personal Page
Personal Album
Photo Albums
Project Albums

Posts: 11447
Comments: 452
Joined: 03/18/05

See our article on "Proper Trailer Setup"
http://www.whalercentral.com/articles...cle_id=117

As wrangler says, raise the motor all the way up and locked when trailering.
You want the boat as low as you can get on the trailer so it is easier to launch and retrieve.

 
Jump to Forum:
Bookmark and Share
Today's Date & Time
November 21, 2024 - 3:32 AM
Visit our Sponsors
Specialty Marine - Parts and Accessories


Wm. J. Mills and Co. - Boston Whaler Canvas


Nauset Marine - Whaler Parts and Accessories


Carver Covers - The Best Covers Under The Sun



Click on logo to visit site
View all Sponsors Here
Users Online
Welcome
AuntiesMontauk
as the newest member

· Guests Online: 10
· Members Online: 0
· Total Members: 50,390
Login
Username

Password

Remember Me


Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.
Top 5 Models Posted
· Montauk 17 1,638
· Sport 13 1,366
· Outrage 18 556
· Nauset 16 402
· Sport 15 365

View all Models Here
Render time: 0.13 seconds Copyright WhalerCentral.com © 2003-2024 86,535,739 unique visits