1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

Sport 15 - Engine Mount/Raise question
roymiz	#1  Posted on 12/22/13 - 9:47 AM
Member Personal Page Posts: 22 Comments: 0 Joined: 10/30/13	15' whaler with a 60HP Yamaha 2-stroke. Please help me understand how my motor is mounted and the best way to go about raising it... I've read many topics on this...and probably more confused now that when i started... **Pls see photos of engine in my personal page....thanks!** - Would like to raise the motor up one notch....but confused on the lower engine mounts.. - Dumb question...but how are the lower bolts mounted to the engine? - I'm guessing if i raise the engine a notch, new holes will need to be drilled...?? Thanks for any input...
wlagarde	#2  Posted on 12/22/13 - 10:45 AM
Member Personal Page Project Albums Posts: 442 Comments: 2 Joined: 07/21/13	I just did this. See here http://www.whalercentral.com/userphot...lbum_id=64 and here http://www.whalercentral.com/forum/vi...rowstart=0. Can you provide a picture of the engine as it is currently mounted so we can see the position and what bolt holes are currently used? Edited by wlagarde on 12/22/13 - 10:46 AM 1976 Sport 15 w/ 2005 50hp Nissan 2 stroke
roymiz	#3  Posted on 12/22/13 - 11:25 AM
Member Personal Page Posts: 22 Comments: 0 Joined: 10/30/13	wlagarde - thanks for the info....pics are in my personal page... thanks!
Joe Kriz	#4  Posted on 12/22/13 - 1:03 PM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	You will not be able to raise the motor just one hole. You will have to raise it 2 holes up by drilling the Green holes in the link below. http://www.whalercentral.com/articles...icle_id=82 wlagarde shows the process in his project album. You will also need to fill the lower "Blind" holes that your motor is mounted in now. It is simple and straight forward. 1. Measure both inside and outside the transom for the "Green" holes to make sure the inside bolts and washers will clear the bottom of the splashwell. (see the diagram on the link above) 2. Drill the "Green" holes. 3. Fill the "Blind" holes. 4. Remount the motor 2 holes up.
wlagarde	#5  Posted on 12/22/13 - 2:34 PM
Member Personal Page Project Albums Posts: 442 Comments: 2 Joined: 07/21/13	roymiz - I don't see a link to your personal page. Have you set it to active? 1976 Sport 15 w/ 2005 50hp Nissan 2 stroke
roymiz	#6  Posted on 12/22/13 - 4:50 PM
Member Personal Page Posts: 22 Comments: 0 Joined: 10/30/13	Thanks to both of you!! Now I understand...
wlagarde	#7  Posted on 12/22/13 - 5:06 PM
Member Personal Page Project Albums Posts: 442 Comments: 2 Joined: 07/21/13	OK - It's as Joe says and entails exactly what I did. You will need to raise the engine two holes. Remove the engine, fill the blind holes, drill the green holes and remount the engine. Edited by wlagarde on 12/22/13 - 6:23 PM 1976 Sport 15 w/ 2005 50hp Nissan 2 stroke