View Thread
Before Posting, Please Read Our Posting Guidelines Below.

1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

 Print Thread
Mounting Engine to 13' sport (1970)
bigut
#1 Print Post
Posted on 09/09/09 - 12:10 PM
Member
Personal Page

Posts: 21
Comments: 0
Joined: 03/06/08

Need help mounting 40 hp 20 inch shaft to my transom, transom has been infilled and is level across the transom. My question is how low should the cavitation plate be below the bottom of the boat, is their any publication or diagram to refer to. Boat overheats and wot, but is fine with three people in it.

Very frustrated

 
Jeff
#2 Print Post
Posted on 09/09/09 - 12:22 PM
User Avatar
Member

Posts: 1987
Comments: 34
Joined: 04/02/05

The cavitation plate should be at or above the bottom of the hull.


Edited by Jeff on 09/09/09 - 12:23 PM
1993 23' Walkaround Whaler Drive
 
Joe Kriz
#3 Print Post
Posted on 09/09/09 - 12:45 PM
User Avatar
Site Owner
Personal Page
Personal Album
Photo Albums
Project Albums

Posts: 11447
Comments: 452
Joined: 03/18/05

Depending on which model engine you have, you probably only have 4 holes in the engine brackets to adjust the height.

The mounting bolt holes are as follows:
1. Bolts in top hole means the engine is mounted all the way down
2. Bolts in second hole from top means engine is mounted one hole up
3. Bolts in third hole from top means engine is mounted two holes up
4. Bolts in bottom holes means the engine is mounted as high as it will go or all the way up.

Each bolt hole is 3/4 of an inch apart so you can raise or lower the engine 3/4 of an inch per bolt hole.

 
moose
#4 Print Post
Posted on 09/09/09 - 1:12 PM
User Avatar
Member
Personal Page

Posts: 543
Comments: 1
Joined: 03/07/07

The transom on that hull "slopes" forward when viewed from top to bottom. the top of the transom is farther aft than the bottom where it meets the hull. That means the water will travel almost a foot from when it leaves the bottom of the hull before it gets to the engine. (I know, the water isn't moving, it's the boat, but you know what I mean) The water will be coming up to meet the engine, so the engine can be mounted with the anticav plate an inch or more above the level of the bottom of the boat. (at static trim). That is where mine is, and it works great.
Mike

 
Joe Kriz
#5 Print Post
Posted on 09/09/09 - 1:20 PM
User Avatar
Site Owner
Personal Page
Personal Album
Photo Albums
Project Albums

Posts: 11447
Comments: 452
Joined: 03/18/05

moose,

And what holes are the bolts in????

 
moose
#6 Print Post
Posted on 09/10/09 - 6:23 AM
User Avatar
Member
Personal Page

Posts: 543
Comments: 1
Joined: 03/07/07

Joe,
That's something that didn't stick in my mind. My old brain only has room for a few things. The important matter for me was where the plate wound up. That's where I bolted it and don't know which hole it's in. I can check for you later if it is needed info.
Mike

 
bigut
#7 Print Post
Posted on 09/10/09 - 9:54 AM
Member
Personal Page

Posts: 21
Comments: 0
Joined: 03/06/08

My bolts are in the top holes. I wiil send a picture

 
Joe Kriz
#8 Print Post
Posted on 09/10/09 - 11:30 AM
User Avatar
Site Owner
Personal Page
Personal Album
Photo Albums
Project Albums

Posts: 11447
Comments: 452
Joined: 03/18/05

bigut,

So that means your engine is mounted all the way down and is probably too low as moose and jeff mentions.

 
Binkie
#9 Print Post
Posted on 09/10/09 - 5:26 PM
User Avatar
Member
Personal Page

Posts: 2012
Comments: 0
Joined: 12/19/05

My 25 4 stroke Merc is mounted on a 6" setback bracket, and the front of the prop is about 24" behind the bottom of the transom. The cavitation plate is 2 1/2" above the bottom, and on plane it rides on the surface.


Rich
 
Tom W Clark
#10 Print Post
Posted on 09/11/09 - 7:33 AM
User Avatar
Member
Personal Page

Posts: 4280
Comments: 7
Joined: 09/30/05

You are surely too low. If the transom is level then it is not even at tall as a factory 20" transom (which was slightly crowned) and the motor will need to be raised several holes.

Remember, you do NOT want the cavitaton plate below the hull. You do not even ant it even with the hull, you want it to be ABOVE the bottom of the hull.

 
CES
#11 Print Post
Posted on 09/11/09 - 7:53 AM
User Avatar
Member
Personal Page
Photo Albums
Project Albums

Posts: 2681
Comments: 7
Joined: 04/27/07

I wish I could post a picture in this thread of how the motor should be mounted. As said in above posts, the cavitation plate should be either level or higher than the bottom of the boat. While on a plane you should be able to clearly see your cavitation plate.


Cliff
1966 13' Sport with a 1993 40hp Yamaha 2 Smoker
 
bigut
#12 Print Post
Posted on 09/11/09 - 8:18 AM
Member
Personal Page

Posts: 21
Comments: 0
Joined: 03/06/08

Look at the pictures in my personal page to see how my motor is mounted now:

http://whalercentral.com/infusions/pe...er_id=8344


Edited by Tom W Clark on 09/11/09 - 8:46 AM
 
Tom W Clark
#13 Print Post
Posted on 09/11/09 - 8:48 AM
User Avatar
Member
Personal Page

Posts: 4280
Comments: 7
Joined: 09/30/05

Yeah, go ahead and raise the motor a hole or two.

Again, I have to disagree with Jeff and Cliff. You do NOT want the cavitation plate even with the bottom of the hull. You want it to be ABOVE the bottom of the hull.

 
Tom W Clark
#14 Print Post
Posted on 09/11/09 - 8:59 AM
User Avatar
Member
Personal Page

Posts: 4280
Comments: 7
Joined: 09/30/05

So getting back to your original post, what is it that frustrates you? Are you saying your motor overheats? If so it has nothing to do with how your motor is mounted.

It also appears that your motor is already mounted, so are you asking how or are are you asking about something else.

 
bigut
#15 Print Post
Posted on 09/11/09 - 9:09 AM
Member
Personal Page

Posts: 21
Comments: 0
Joined: 03/06/08

I feel the motor lose pressure when I go faster, the pickup is either in the bubbles or out of the water and thats when it heats up.

 
moose
#16 Print Post
Posted on 09/11/09 - 9:12 AM
User Avatar
Member
Personal Page

Posts: 543
Comments: 1
Joined: 03/07/07

Can you give a better description of losing pressure?
Mike

 
bigut
#17 Print Post
Posted on 09/11/09 - 9:55 AM
Member
Personal Page

Posts: 21
Comments: 0
Joined: 03/06/08

Yes, Water pressure, the engine will lose hp and then gain it back, like it is losing grip with the water.

 
Derwd24
#18 Print Post
Posted on 09/11/09 - 10:16 AM
User Avatar
Member

Posts: 1607
Comments: 9
Joined: 05/09/07

When you say it overheats at WOT, is that by an alarm or a temp gauge?

And does the overheat happen at the same time as the loss in WOT rpm?


Edited by Derwd24 on 09/11/09 - 10:17 AM
Dave - 1983 Outrage 22
 
CES
#19 Print Post
Posted on 09/11/09 - 11:30 AM
User Avatar
Member
Personal Page
Photo Albums
Project Albums

Posts: 2681
Comments: 7
Joined: 04/27/07

From looking at your PP, it appears that you may want to raise your engine up one hole to start. Your cavitation plate appears to be level or slightly below the bottom of your hull.


Cliff
1966 13' Sport with a 1993 40hp Yamaha 2 Smoker
 
bigut
#20 Print Post
Posted on 09/11/09 - 12:18 PM
Member
Personal Page

Posts: 21
Comments: 0
Joined: 03/06/08

It does on the temp gauge, I bought a surface mount gauge it would read 200 f at the start, when I had the problem it went to 240. I since have purchased a internal sender and the gauge reads at 170 in the driveway, I am going to raise the engine 1 hole and watch the gauge.

Thanks

 
Jump to Forum:
Bookmark and Share
Today's Date & Time
November 25, 2024 - 11:27 PM
Visit our Sponsors
Wm. J. Mills and Co. - Boston Whaler Canvas


Carver Covers - The Best Covers Under The Sun


Specialty Marine - Parts and Accessories


Nauset Marine - Whaler Parts and Accessories



Click on logo to visit site
View all Sponsors Here
Users Online
Welcome
AuntiesMontauk
as the newest member

· Guests Online: 2
· Members Online: 0
· Total Members: 50,390
Login
Username

Password

Remember Me


Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.
Top 5 Models Posted
· Montauk 17 1,638
· Sport 13 1,366
· Outrage 18 556
· Nauset 16 402
· Sport 15 365

View all Models Here
Render time: 0.27 seconds Copyright WhalerCentral.com © 2003-2024 86,559,877 unique visits