View Thread
Before Posting, Please Read Our Posting Guidelines Below.

1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

 Print Thread
Rubber wheels in wood riser/seat clamp
NoncChuRouge
#1 Print Post
Posted on 10/09/24 - 12:34 PM
Member

Posts: 5
Comments: 0
Joined: 12/09/20

Hello, 13’ 1964 Whaler Sport. I’m in the process of replacing my wood kit on my whaler. Does anyone know where to find the rubber wheel inserts on the risers? Can they be left off of the new build? I’m cutting some new risers myself and I’m not sure where to find them or if they’re really needed. I know what they’re for but if I can’t find them I’ll probably just bungee the front one down and figure something out for the rear bench seat but if they’re readily available I’ll probably cut a hole for them and install them. Thanks

 
Phil T
#2 Print Post
Posted on 10/09/24 - 4:22 PM
User Avatar
Administrator
Personal Page
Personal Album
Project Albums

Posts: 7043
Comments: 6
Joined: 03/26/05

Need to see a photo of the trailer to give you targeted advice.


1992 Outrage 17 I
2019 E-TEC 90, Viper 17 2+
2018 Load Rite Elite 18280096VT
 
NoncChuRouge
#3 Print Post
Posted on 10/09/24 - 7:24 PM
Member

Posts: 5
Comments: 0
Joined: 12/09/20

Thanks but I’m not talk about the trailer risers. I’m talking about the mahogany wood on the interior of the 13’ Whaler. It has 2 risers/seat clamps that hold the thwart bench seats in place. The factory ones had small rubber wheels or plugs that held the bench seats in place and stopped them from vibrating. The front seat is also removable and it helped hold it in place.

 
Phil T
#4 Print Post
Posted on 10/10/24 - 7:42 AM
User Avatar
Administrator
Personal Page
Personal Album
Project Albums

Posts: 7043
Comments: 6
Joined: 03/26/05

Any hardware store would have them.


1992 Outrage 17 I
2019 E-TEC 90, Viper 17 2+
2018 Load Rite Elite 18280096VT
 
Tom Hemphill
#5 Print Post
Posted on 10/10/24 - 2:45 PM
Member
Personal Page

Posts: 136
Comments: 1
Joined: 01/19/08

In my previously-owned 1966 13-foot Sport, what was there looked possibly home-made. They were rubber disks about 5/8" diameter and 3/16" thick. They were housed in a mortised slot, retained with a brass pin through the center. The closest equivalent that I can find at McMaster-Carr (a great source of obscure hardware) is "cushioning washers." I think they are a great way to retain the thwart seats, and should be replicated.


Edited by Tom Hemphill on 10/10/24 - 2:47 PM
 
NoncChuRouge
#6 Print Post
Posted on 10/14/24 - 5:12 AM
Member

Posts: 5
Comments: 0
Joined: 12/09/20

Thanks Tom. I’ll check McMaster Carr to see what I can find.

 
Joe Kriz
#7 Print Post
Posted on 10/16/24 - 7:43 PM
User Avatar
Site Owner
Personal Page
Personal Album
Photo Albums
Project Albums

Posts: 11447
Comments: 452
Joined: 03/18/05

Here is a direct link for those that may need these:
https://www.mcmaster.com/products/cus...-washers~/

 
Jump to Forum:
Bookmark and Share
Today's Date & Time
November 20, 2024 - 10:21 PM
Visit our Sponsors
Wm. J. Mills and Co. - Boston Whaler Canvas


Nauset Marine - Whaler Parts and Accessories


Specialty Marine - Parts and Accessories


Carver Covers - The Best Covers Under The Sun



Click on logo to visit site
View all Sponsors Here
Users Online
Welcome
AuntiesMontauk
as the newest member

· Guests Online: 3
· Members Online: 0
· Total Members: 50,390
Login
Username

Password

Remember Me


Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.
Top 5 Models Posted
· Montauk 17 1,638
· Sport 13 1,366
· Outrage 18 556
· Nauset 16 402
· Sport 15 365

View all Models Here
Render time: 0.18 seconds Copyright WhalerCentral.com © 2003-2024 86,533,720 unique visits