1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

Outrage 18 instrument panels
innerarity	#1  Posted on 05/30/19 - 7:54 AM
Member Posts: 9 Comments: 1 Joined: 08/06/09	I am looking for two parts needed for refurbishing a 1988 18 Outrage. The specific parts are for two panels located on the center console. They are described by Whaler as Panel-Switch-Port and Panel-Switch-Starboard. The original Whaler parts numbers were 12344600 and 12345600 but both have been discontinued, as would be the case for the age of the part. Thanks. (edited subject for specificity) Edited by Phil T on 05/30/19 - 8:09 AM
Phil T	#2  Posted on 05/30/19 - 8:07 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	Are you looking for the blank instrument panels or ones already cut with switches installed? Blank panels can be obtained. Have you contacted Sue Lodel, Parts Manager, Beacon/Twin Cities Marine? Best source for OEM parts. www.beacontcm.com 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT
innerarity	#3  Posted on 05/30/19 - 5:49 PM
Member Posts: 9 Comments: 1 Joined: 08/06/09	Thanks so much Phil. I will give her a call.
innerarity	#4  Posted on 06/18/19 - 1:45 PM
Member Posts: 9 Comments: 1 Joined: 08/06/09	Phil, Sue didn't have a replacement part. She referred me to Ultra Panel Marine Company, a previous manufacturer, in Miami. They said the parts had been discontinued for years. Any other suggestions who might have REAL old parts ?? Thanks for your help on this.
Phil T	#5  Posted on 06/19/19 - 8:36 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	Members have made replacements as a DIY. The panels are aluminum. I would cut the holes for the gauges and switches and the corners first then paint with a self etching primer then Rustoleum black flat or satin finish. 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT
action	#6  Posted on 06/19/19 - 12:57 PM
Member Personal Page Posts: 208 Comments: 2 Joined: 01/03/15	I recently replaced a panel on my 1988 Montauk. Sue Lodel was able to provide a replacement. Before I contacted her I was going to use a vendor called New Wire Marine. They will make you what you want and pricing was pretty good. The panels are no metal though. They had very good reviews on some other sites and were helpful over the telephone. https://newwiremarine.com/product/e-p...l-builder/ [fixed link] Edited by Phil T on 06/19/19 - 2:16 PM
Joe Kriz	#7  Posted on 06/19/19 - 2:38 PM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	innerarity, Did you ask Sue Lodel for this panel part number? http://www.whalercentral.com/photogal...hoto_id=84 That is a replacement panel for the Classic Montauk, Outrages etc. Basic difference is the white line layout. Check the White line out you have.
innerarity	#8  Posted on 06/21/19 - 12:56 PM
Member Posts: 9 Comments: 1 Joined: 08/06/09	Thanks so much to all for your suggestions. I talked again with Sue and she can find the vertical panels on either side of the steering wheel but the horizontal panels are not to be found. She again suggested having them made at Ultra Marine. Screen printing the names of each switch may or may not be able to be done. Maybe I can find someone selling parts from an old 18 Outrage and can obtain the panels that way. I appreciate everyone's help !
biggiefl	#9  Posted on 07/18/19 - 12:02 PM
Member Posts: 890 Comments: 4 Joined: 05/08/06	Make them out of teak. It would look OEM and then put modern Rockers in it. I did that on my 19 Banana and it looked great. 24 Whalers so far....