1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

1988 17' Montauk Brass Drains
michaux	#1  Posted on 04/23/19 - 12:10 AM
Member Posts: 8 Comments: 0 Joined: 05/30/10	Hi from New Zealand, I am finishing a minor revamp of my Montauk that has had relatively little use since new. How do I know if I need to replace the 4 drains? I assume they are original. If I do need replacements, is there an article on how to do this? Are any special tools needed? (I am in New Zealand, so mail order from the USA is not easy) Thanks in advance P.S. In case anyone has advice, I am looking to 1 renew the cooler seat cushion, if anyone has a suggestion where to source 2 move the battery to inside the console (I need to know how best to support the floor under the battery) Edited by michaux on 04/23/19 - 12:15 AM
Phil T	#2  Posted on 04/23/19 - 5:19 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	If the tube is loose, corroded or if the O ring is dry and cracked, then replace. (if the tubes, O ring are okay, I apply Boat Life sealant (not adhesive) around the tube for added protection.) https://www.amazon.com/dp/B0009TS57C/...8&th=1 1" Drain tubes and flare tool available on Amazon.nz https://www.amazon.com/Moeller-021003...&psc=1 Tool: https://www.amazon.com/520290-1-Drain...amp;sr=8-1 For the O rings, I would order from US. They are light and small so shipping not too bad. Best source is Sue Lodel at Twin Cities Marine. She ships international on a daily basis. Just email her year, model and what you doing, parts you need. Tell her we sent you. www.beacontcm.com Here is an article on How-to http://www.whalercentral.com/articles...icle_id=42 Edited by Phil T on 04/23/19 - 5:21 AM 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT
Phil T	#3  Posted on 04/23/19 - 5:30 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	As for cushions, what do you have now? Are they original? From Our Resources/Parts index: Cooler: http://www.whalercentral.com/photogal...hoto_id=42 RPS:http://www.whalercentral.com/photogal...hoto_id=44 Rod Back: http://www.whalercentral.com/photogal...oto_id=303 There is a OEM manufacturer here but as you know shipping is steep. A owner in So. England just ordered his. The wait was not too long but the shipping and VAT was $$$. I would use a general all purpose cleaner and a stiff brush to clean the vinyl. Stay away from any product that has an acid since it will dissolve the stitching. 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT
Phil T	#4  Posted on 04/23/19 - 5:32 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	When moving the battery to the console, trace the battery box outline on the floor and then cut it out and have the case sit inside and rest on the deck. It also gives you a bit more room. I had the box sit on a square of Dri-Dek to prevent damage to the gelcoat. 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT
Phil T	#5  Posted on 04/23/19 - 5:47 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	Frank, please check your email address in your profile. The domain name is invalid. 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT