|
Raw Water Washdown - 2006 235 Conquest
|
| eazyeasty |
Posted on 02/19/17 - 3:03 PM
|
Member
Posts: 3
Comments:
0
Joined: 02/19/17
|
Hi Guys - having problems with my raw water wash down. Just looked up raw water wiring diagram. Do I need to run the live well pump as well as raw water wash down pump? When boat is out of the water all other live well pumps work but not the raw water pump - no noise at all.The seacock valve is open so no water flow problems should be stopping it - we just can't hear any pump running. Hoping this is something simply....any help is appreciated
|
| |
|
|
| butchdavis |
Posted on 02/19/17 - 4:19 PM
|
Member
Posts: 838
Comments:
0
Joined: 11/22/11
|
It doesn't make sense to me that the live well pump would have to be one for the raw water wash down pump to operate.
First I would check the circuit breaker near the switch to see if it has tripped or the fuse if it has one. If that isn't the problem I would work my way from the switch to the battery and the pump to make sure no conductors are parted or have loose or oxidized connections.
Finally, if your raw water wash down system was not a factory installed option I would physically check to see if it has a dedicated pump. Many owners add raw water wash down systems to their boats that use the live well pump for the wash down. This is accomplished by adding plumbing to the existing live well pump discharge and sometimes a "Y" valve.
Butch |
| |
|
|
| eazyeasty |
Posted on 02/19/17 - 5:37 PM
|
Member
Posts: 3
Comments:
0
Joined: 02/19/17
|
Thanks Butch - looks from factory. will check fuses again. as wiring is all hidden + the amount of wiring that comes with the 235 Conquest might be hard for me to diagnose. I'm sure its something simple like user error - really appreciate your help!
|
| |
|
|
| butchdavis |
Posted on 02/21/17 - 6:30 AM
|
Member
Posts: 838
Comments:
0
Joined: 11/22/11
|
It just occurred to me that there is an easy test of the pump that could save you a lot of troubleshooting effort. Run two conductors directly from the battery terminals to the pump. If it runs the problem lies in the circuit. If not, replace the pump.
Butch |
| |
|
|
| jollyrog305 |
Posted on 02/21/17 - 10:04 AM
|
Member
Personal Page
Posts: 200
Comments:
0
Joined: 01/15/08
|
I agree with Butch – see if the pump works…The live well and raw water work independent of each other (separate switches), however they share the same seacock. The live well pump is located just above the seacock, the raw water should be located on a bulkhead. If this pump was run without the seacock open, it may have burned out
|
| |
|
|
| eazyeasty |
Posted on 02/21/17 - 3:04 PM
|
Member
Posts: 3
Comments:
0
Joined: 02/19/17
|
thanks Guys - it would appear there is also a pressure switch on the motor so it will only work when water is detected, therefore activating the pump so will be intresting to see what happens when we by pass.
So in short the raw water pump will suck up through the livewell pump in the hull? never seen that before - that is how mine is set-up anyways.
keep on troubleshooting I guess - appreciate it lads!
|
| |
|
|
| butchdavis |
Posted on 02/22/17 - 6:42 AM
|
Member
Posts: 838
Comments:
0
Joined: 11/22/11
|
I believe the pressure switch is to shut off the pump when the discharge pressure is high. This allows you to use a spray nozzle on the end of the wash down hose by turning the pump off when the nozzle is closed. Otherwise the battery could be rundown while fishing if you failed to turn the dashboard switch off after washing blood, etc off the deck. The pump test we described should not be affected by the pressure switch if my assumption is correct.
Butch |
| |
|
