1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

De Persia scupper model 49417
bryan wheeler	#1  Posted on 02/02/17 - 7:49 AM
Member Posts: 5 Comments: 0 Joined: 02/01/07	I have a 1986 Outrage Cuddy 22 and am looking to replace the engine well scupper.I want to replace it with the factory original part.That part is a De Persia and has the number 49417 on it.If anyone has one or knows where I can purchase please contact me.Thanks Edited by bryan wheeler on 02/02/17 - 7:50 AM
Phil T	#2  Posted on 02/02/17 - 8:08 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	Bryan - I presume this is for the I/O model. Easiest path is to contact Sue Lodel, Parts Manager, Twin Cities Marine. She is a parts guru and they are a Master Whaler dealer. www.beacontcm.com 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT
bryan wheeler	#3  Posted on 02/02/17 - 1:01 PM
Member Posts: 5 Comments: 0 Joined: 02/01/07	Thanks for the quick response Phil.I should have posted more info in my original post to include that the boat is an outboard model.I contacted Sue a couple weeks ago and was told the part is no longer available so I figured I would reach out to the Whaler community and see if anyone had one they are willing to sell.
Joe Kriz	#4  Posted on 02/02/17 - 1:25 PM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	I have never seen factory Scuppers on that model. Do you have any photos to share?
Phil T	#5  Posted on 02/03/17 - 5:44 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	Did Sue have a substitute? 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT
bryan wheeler	#6  Posted on 02/03/17 - 9:59 AM
Member Posts: 5 Comments: 0 Joined: 02/01/07	Will do Joe...I'll try to get a couple of pictures this weekend and get them posted. I was hesitant to call it a scupper but it's a clear plastic housing that has a ping pong ball in it that restricts water flow in one direction.It is mounted in the engine well and allows the water to run out of the fishwell to the motor well. Phil, there are other options but I am trying to find an original one before I travel down that road. Thanks for the help!
Phil T	#7  Posted on 02/03/17 - 10:44 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	You can use the ball type scupper. Here are two of the most common: http://thmarine.com/flow-max-ball-scu...ll-scupper https://www.jamestowndistributors.com...?pid=12158 Phil T attached the following image: [34.31Kb] 1992 Outrage 17 I 2019 E-TEC 90, Viper 17 2+ 2018 Load Rite Elite 18280096VT
gchuba	#8  Posted on 02/05/17 - 7:30 AM
Member Posts: 1675 Comments: 0 Joined: 03/31/13	I removed and sealed that scupper hole in my transom. It was just an inch or two above the bottom of the splash well. If I still have it (may have thrown it out) yours free if I run across it. Are you keeping your boat factory original? That ball assembly never worked for me. Garris
bryan wheeler	#9  Posted on 02/17/17 - 12:33 PM
Member Posts: 5 Comments: 0 Joined: 02/01/07	Garris,That would be fantastic! if you do run across it I would love to have it,and yes i'm trying to keep it factory original.