1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

stern light placement, windshield gasket 1965 Sakonnet
seamac101	#1  Posted on 06/02/15 - 9:05 AM
Member Posts: 8 Comments: 0 Joined: 06/02/15	can original nav wires be re-run? who sells white windshield gaskets? and last is there any mounting diagram for stern light placement? thanks, charlie (changed abbreviated boat name from sak to Sakonnet for clarification) Edited by Joe Kriz on 06/02/15 - 10:18 AM
Phil T	#2  Posted on 06/02/15 - 9:41 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	What model and year do you have?
seamac101	#3  Posted on 06/02/15 - 10:30 AM
Member Posts: 8 Comments: 0 Joined: 06/02/15	sorry, 1965 sakonnet
seamac101	#4  Posted on 06/02/15 - 10:36 AM
Member Posts: 8 Comments: 0 Joined: 06/02/15	The original wire is down in factory hole but not enough to grab. transom has been re-gelled not sure stern light mounts are in correct place. freshwater boat still has factory window seals want to replace thanks,charlie
Weatherly	#5  Posted on 06/02/15 - 10:46 AM
Member Posts: 752 Comments: 4 Joined: 12/31/06	For the window gasket material, look at this thread: http://www.whalercentral.com/forum/vi...ost_123590
seamac101	#6  Posted on 06/02/15 - 10:48 AM
Member Posts: 8 Comments: 0 Joined: 06/02/15	Should stern light mount straight up left to right or should it follow the angle of transom, being angled slightly to port. not forward/backwards angle side to side angle only. Just want to get it right
seamac101	#7  Posted on 06/02/15 - 10:48 AM
Member Posts: 8 Comments: 0 Joined: 06/02/15	thanks
Joe Kriz	#8  Posted on 06/02/15 - 11:05 AM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	You will want to look in our Downloads section under Installation and Parts Breakdown Sheets and download the Stern Light Installation Instructions. http://www.whalercentral.com/download...owstart=15 These lights were mounted on either the Stern or the Port side depending on the year. Yours most likely is mounted on the Port side. You can look at other Sakonnet models in the members personal page section. http://www.whalercentral.com/viewpage...page_id=65 http://www.whalercentral.com/infusion...er_id=8412
seamac101	#9  Posted on 06/03/15 - 5:35 PM
Member Posts: 8 Comments: 0 Joined: 06/02/15	Thanks Joe big help all the holes were in the right spot. Still wondering if i can pull a new nav wire through the factory run in the hull? does the old wire just run through the boat flotation material or does it have a dedacated run built into the hull? thanks again,Charlie
Phil T	#10  Posted on 06/04/15 - 10:40 AM
Administrator Personal Page Personal Album Project Albums Posts: 7043 Comments: 6 Joined: 03/26/05	New wires for the bow navigation light should be run via the rubrail. The original bow light wire is through the foam, no dedicated run.