1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

1987 18' BW outrage 3 hook Gunwale specs
stixz	#1  Posted on 03/30/14 - 10:11 AM
Member Posts: 24 Comments: 0 Joined: 02/24/14	Hello, Does any have the information or link on the specs for the original teak gunwale? I recently acquired BW outrage and it was missing. I would like to make a replace. I'm looking for something like this http://www.whalercentral.com/photogal...oto_id=804 Thanks in Advance, Rolando- Edited by Joe Kriz on 03/30/14 - 10:21 AM
Joe Kriz	#2  Posted on 03/30/14 - 10:24 AM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	Look in the Downloads section. We have the drawing for the 3 hook even though the diagram only shows 2. http://www.whalercentral.com/download...owstart=15 Edited by Joe Kriz on 03/30/14 - 10:33 AM
stixz	#3  Posted on 03/30/14 - 10:50 AM
Member Posts: 24 Comments: 0 Joined: 02/24/14	Thanks Joe!
gchuba	#4  Posted on 03/30/14 - 11:21 AM
Member Posts: 1675 Comments: 0 Joined: 03/31/13	I built several identical ones for my 1979 22 ft Revenge. I had a good one to scribe from. I used 3/4 " marine mahogany plywood. If you contact me through my personal page, I will be glad to scribe it on piece of paper and mail you the pattern. I used a hole saw for the center circles and cut the uprights to the circles with a small Delta band saw with a thin blade. The edge that fits directly up against the hull underneath the gunwale is tapered and needs to be custom fit. I actually had a couple of original pieces to scribe from, they were not perfectly identical, just very close. gchuba Edited by gchuba on 03/30/14 - 11:22 AM
Marko888	#5  Posted on 03/30/14 - 1:13 PM
Member Project Albums Posts: 413 Comments: 10 Joined: 05/26/08	I purchased beautiful replica's from Walter at black duck gallery. They appear to be a perfect match and the price was reasonable relative to the high quality. Edited by Marko888 on 03/30/14 - 1:14 PM
gchuba	#6  Posted on 03/30/14 - 1:53 PM
Member Posts: 1675 Comments: 0 Joined: 03/31/13	Marko, total agreement. If I did not have use for the spoils/remainder of the sheet of marine plywood, I think the cash out of pocket would have been close to a "wash" in cost. If you have the material around they are fun to make. When I held the full originals together, as well as the remnants of the originals, it appears to me that these were a hand made custom fit from Whaler. gchuba Edited by gchuba on 03/30/14 - 2:01 PM
stixz	#7  Posted on 03/31/14 - 1:47 PM
Member Posts: 24 Comments: 0 Joined: 02/24/14	Gchuba, agreed. I think the price would be a "wash." Since I have to hunt down the wood, gas, sand paper, and labor; then the chance it might not come out the way I wanted. Thanks, Marko that was the site I had in mind. BTW. Specialty Marine, has the 2 hook gunwale in teak and already varnished. But I'm thinking of going for the 3 hook from BDG.