1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

Rail Mount Cup Holders
Jay Fitz	#1  Posted on 06/15/13 - 3:52 PM
Member Personal Page Posts: 343 Comments: 0 Joined: 09/08/10	While cruising today with the fam, I realized that we have nowhere to put our drinks. I want to get a few rail mount cupholders to attach around the console of a Montauk. Any recommendations? Something that looks OK, holds up well, and doesn't cost a fortune? Thanks.
contender250	#2  Posted on 06/15/13 - 5:35 PM
Member Posts: 363 Comments: 0 Joined: 10/09/11	I would look for the ones that have/attached by suction cups, No holes drilled and when they break just get a new one. Another thought is attach one to your belt, The drink would never be out of reach....
Joe Kriz	#3  Posted on 06/15/13 - 5:56 PM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	Mug Buoy by Orbex. http://www.propoweronline.com/orbex-r...esults.htm Make sure to purchase the Stainless Steel version of the rail clamp. http://users.sisqtel.net/jkriz/Montau...onsole.jpg
Jay Fitz	#4  Posted on 06/15/13 - 6:27 PM
Member Personal Page Posts: 343 Comments: 0 Joined: 09/08/10	Thanks Joe! I knew I saw those somewhere...on your console! What size are the rails BTW, less than 1"?
Joe Kriz	#5  Posted on 06/15/13 - 6:31 PM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	Your rails are 7/8'. Some later rails are 1". Most rail mounts fit both 7/8" and 1" which these do.
mct	#6  Posted on 06/15/13 - 6:53 PM
Member Personal Page Posts: 41 Comments: 0 Joined: 05/10/10	My wife recently pointed out the same fact. I bought a cup holder from Cuda's Customs. No screw holes. I mounted mine on the vertical railing just to the left of the helm on my 18' Outrage. The cup holder will "twist" but it will not slide up and down. Have used it a couple of times and so far so good. I will probably order another one for the other side. They have a number of different styles. Only took a couple of days arrive in the mail.
mct	#7  Posted on 06/15/13 - 7:03 PM
Member Personal Page Posts: 41 Comments: 0 Joined: 05/10/10	I posted a photo of the cup holder on my personal page.
Jay Fitz	#8  Posted on 06/15/13 - 7:59 PM
Member Personal Page Posts: 343 Comments: 0 Joined: 09/08/10	Joe Kriz wrote: Make sure to purchase the Stainless Steel version of the rail clamp. I've found that exact holder listed at many different sites and none of them say what the mount is made of and they don't show a SS option.
mct	#9  Posted on 06/15/13 - 8:34 PM
Member Personal Page Posts: 41 Comments: 0 Joined: 05/10/10	The holder is made of plastic. It comes in two pieces that fit around the railing and is secured with two screws. I put a Tervis Tumbler in mine and it seems to be well built. I ordered directly from Cuda's Customs. http://www.cudascustoms.com/products.htm. There should be a 7/8 SS option.
wannabe	#10  Posted on 06/16/13 - 5:55 AM
Member Posts: 287 Comments: 1 Joined: 06/03/09	After finally getting my boat back together enough to go for a ride this weekend, I am in the market for some drink holders. My passenger was surprised the boat didn't have any and even more surprised I wouldn't drill holes to install any. I like location that were in the images Joe provided. Hope it works for my Outrage. Drew 1988 Outrage 18 - 1988 Yamaha 130 hp