1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

casting platforms for a Montauk 17
Fishnutz	#1  Posted on 08/20/09 - 1:11 PM
Member Posts: 5 Comments: 0 Joined: 07/21/09	Any body got some ideas on building a stern casting platform or pictures?
Joe Kriz	#2  Posted on 08/20/09 - 2:46 PM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	I would take a look at all the Montauk in the personal page section to get some ideas. Some people made their own stern platforms. http://www.whalercentral.com/viewpage...page_id=65
Bake	#3  Posted on 08/20/09 - 3:04 PM
Member Personal Page Project Albums Posts: 902 Comments: 8 Joined: 01/30/06	I have what I think is a factory option rear casting platform for a 17 It is fiberglass with a little fish well molded in the center. I do not see your e mail in your profile. Send me your email address and I will send you some measuerments and pictures. Edited by Bake on 08/20/09 - 7:57 PM
Guts	#4  Posted on 08/20/09 - 3:46 PM
Member Personal Page Posts: 612 Comments: 8 Joined: 11/21/08	I would like to see it. my email is in my PP... I have no idea what this is? Thanks
Guts	#5  Posted on 08/20/09 - 7:49 PM
Member Personal Page Posts: 612 Comments: 8 Joined: 11/21/08	Blake thank you for the email I have never seen this type of platform before. Do you want to sale it? If it is factory equipment I think Joe Kriz might like to add the pictures to the site. I will not forward to Joe / these are your your pictures. Thanks again... Guts/AKA/Kim
Joe Kriz	#6  Posted on 08/20/09 - 7:52 PM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	There were some platforms for the Striper and Bass models from the factory if I remember correctly. Always interested in photos....
Alabama Whaler	#7  Posted on 08/21/09 - 6:21 AM
Member Posts: 11 Comments: 0 Joined: 08/15/07	Fish: Previous owner of my family's 17' whaler crafted a forward, hinged casting platform from mahogany planks (possibly the original bench seats from what I now know was a super sport model). I have it disassembled at present for refinishing. I can take some pictures of the wood back in 'original' to me locations (mostly; some wood will have to be replaced) in a few weeks when I'm back at the beach. Basically, 1" square x 2' long or so narrow runners go down the inside lip of the hull. The planks (2 @ approx. 1"x12"x5'; 1 @ approx 1" x 4" x 5' cross the hull and rest on the runners forming the top of the platform. Two sets of double hinges allow access inside the platform. The back side of the platform (facing center console) was some type of thin fiberglass. It was not watertight and eventually deteriorated as the boat has aged. I am looking for a replacement piece, and considering different options for the material. It was thin (maybe 1/8" thick), but it was cut to match the concave contour of the hull up front. You wouldn't have that problem in the stern since the floor is basically flat (except for small drainage channels). jb "Alabama Whaler"