1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

Mounting Cooler Cleats
modenacart	#1  Posted on 01/02/11 - 6:29 PM
Member Personal Page Posts: 741 Comments: 4 Joined: 02/28/09	What mounting hardware was used for mounting the cooler cleats? Also, does anyone have a picture of them installed on the boat? Thanks. Edited by modenacart on 01/02/11 - 6:37 PM They that give up essential liberty to obtain a little temporary safety deserve neither liberty or safety. --Benjamin Franklin
Joe Kriz	#2  Posted on 01/02/11 - 10:11 PM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	Montauk cooler cleat drawings can be viewed in the download section. The drawing calls for #10 x 2 inch Edited by Joe Kriz on 01/03/11 - 9:50 AM
modenacart	#3  Posted on 01/03/11 - 6:46 PM
Member Personal Page Posts: 741 Comments: 4 Joined: 02/28/09	Thanks for the drawing. I still don't know how they mount on the boat. Does anyone have a picture of them mounted? They that give up essential liberty to obtain a little temporary safety deserve neither liberty or safety. --Benjamin Franklin
Joe Kriz	#4  Posted on 01/03/11 - 9:21 PM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	Take a look at this attachment. Joe Kriz attached the following image: [43.32Kb]
modenacart	#5  Posted on 01/04/11 - 2:16 PM
Member Personal Page Posts: 741 Comments: 4 Joined: 02/28/09	Ok, great, so the cooler just sits on top of it. I wasn't sure because I saw this picture. [img]http://www.whalercentral.com/forum/attachments/woodfinish03.jpg[/img] It didn't seem right They that give up essential liberty to obtain a little temporary safety deserve neither liberty or safety. --Benjamin Franklin
Joe Kriz	#6  Posted on 01/04/11 - 4:39 PM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	Outrage coolers sit on the floor with the cleats on the outside. Montauk coolers sit on top of the cleats so the cooler clears the slanted floor sides.
modenacart	#7  Posted on 01/04/11 - 6:50 PM
Member Personal Page Posts: 741 Comments: 4 Joined: 02/28/09	Thanks for the information They that give up essential liberty to obtain a little temporary safety deserve neither liberty or safety. --Benjamin Franklin
modenacart	#8  Posted on 01/05/11 - 1:10 PM
Member Personal Page Posts: 741 Comments: 4 Joined: 02/28/09	About how far apart are the cleats to each other? Also, it looks like there is a location to add a hook to the side of the cooler, where do you get the hook? They that give up essential liberty to obtain a little temporary safety deserve neither liberty or safety. --Benjamin Franklin
Joe Kriz	#9  Posted on 01/05/11 - 3:30 PM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	Take another look at the photo I attached above. The cleats can only go out so far until the floor starts to angle. I have also seen them mounted along the edge of the flat section where the non-skid ends. That will give you a good line. For the Cooler Hooks, look in the "OEM Part Photos" link on the left sidebar.
modenacart	#10  Posted on 01/05/11 - 4:18 PM
Member Personal Page Posts: 741 Comments: 4 Joined: 02/28/09	My hull is the non smirked hull. It looks a bit different so I will see now how it lines up. They that give up essential liberty to obtain a little temporary safety deserve neither liberty or safety. --Benjamin Franklin
modenacart	#11  Posted on 01/05/11 - 5:57 PM
Member Personal Page Posts: 741 Comments: 4 Joined: 02/28/09	I didn't have the same lines so I just moved them around until I was happy They that give up essential liberty to obtain a little temporary safety deserve neither liberty or safety. --Benjamin Franklin
Joe Kriz	#12  Posted on 01/05/11 - 6:29 PM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11447 Comments: 452 Joined: 03/18/05	Any Photos? Any measurements?
modenacart	#13  Posted on 01/06/11 - 2:20 PM
Member Personal Page Posts: 741 Comments: 4 Joined: 02/28/09	The top of the cleats are about 15 inches apart and the bottom corners are just under 23 inches apart. I tried to insert photos from my uploaded photos but I can't get it to work. Edited by modenacart on 01/06/11 - 2:23 PM They that give up essential liberty to obtain a little temporary safety deserve neither liberty or safety. --Benjamin Franklin