1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

In Need Of An OMC Outboard Wiring Harness Fabricator
Raider19	#1  Posted on 01/29/18 - 9:55 PM
Member Posts: 15 Comments: 0 Joined: 09/10/17	Hello, I'm relocating a console on an 1990 Rigid Raider 19' with twin 2001 70 horse power OMC outboards. Replacing all electronics and cabling, I'm looking for a fabricator to build the wiring harness and possibly an instrument panel with new gauges. Does anyone have a USA based custom boat wiring company to recommend? Thank you, Abe
Weatherly	#2  Posted on 01/30/18 - 5:34 AM
Member Posts: 754 Comments: 4 Joined: 12/31/06	The 2001 Johnson/Evinrude 70 hp outboard (two stroke) used the Modular Wiring System (MWS) control harness that is still manufactured in assorted lengths and is the same harness used in the Evinrude E-Tec outboard motors. You can buy MWS harnesses on Amazon for reasonable cost, e.g., a 20 foot cable costs $125.07. The MWS is plug and run design to new compatible gauges. You do not need a custom fabricator for new length engine harnesses. Edited by Weatherly on 01/30/18 - 8:32 AM
Raider19	#3  Posted on 01/30/18 - 9:25 PM
Member Posts: 15 Comments: 0 Joined: 09/10/17	Thanks Weatherly. I checked the MWS harnesses on Amazon and ultimately Leaders RPM, just pretty much proving I'm an electrical cretin. I've over complicated my console wiring 10 fold, still need to address trim/tilt wiring from the dated dual Binnacle control, added gauges, fuel flow meter, lighting, radar, etc,. Good lead though, everything could likely be pieced together for a fraction of fab cost, will keep perusing options. Appreciate the input.
Joe Kriz	#4  Posted on 01/31/18 - 9:57 AM
Site Owner Personal Page Personal Album Photo Albums Project Albums Posts: 11430 Comments: 452 Joined: 03/18/05	Raider, I strongly suggest looking at all the articles on this site or a bare minimum of the Site Map. http://www.whalercentral.com/infusion...te_map.php While there, take a look at all the OMC/Bombardier Binnacles, Switch Assemblies and Gauges You might see something else you might need. Look at the second photo in this article under 1996 and Newer Outboard Motor Controls and where it says "1995 & Older" Add 2 Pc twin lead adapter P/N 176516 $8.99 http://www.whalercentral.com/articles...icle_id=56 eBay https://www.ebay.com/itm/NEW-OEM-John...1329961946 https://d3inagkmqs1m6q.cloudfront.net...tboard.jpg
Raider19	#5  Posted on 01/31/18 - 11:55 PM
Member Posts: 15 Comments: 0 Joined: 09/10/17	Joe, Thank you for the links, great info. Abe
EJO	#6  Posted on 02/01/18 - 10:41 AM
Member Personal Page Posts: 669 Comments: 6 Joined: 11/25/12	Abe if you decide to get something from Leaders RPM let me know as they are less than a half mile from my home and I can physically check something for you or take a specific picture of the part. Skipper E-J m/v "Clumsy Cleat" a 2008 Montauk 150
Raider19	#7  Posted on 02/02/18 - 10:27 PM
Member Posts: 15 Comments: 0 Joined: 09/10/17	Hey thank you for the generous offer EJO, very kind of you. Slid off my saddle for a bit to learn something about the wiring system, well worth the pause. Awfully grateful for your offer though. Cheers!
EJO	#8  Posted on 02/05/18 - 11:56 AM
Member Personal Page Posts: 669 Comments: 6 Joined: 11/25/12	your welcome happy sparking I mean boating Skipper E-J m/v "Clumsy Cleat" a 2008 Montauk 150