View Thread
Before Posting, Please Read Our Posting Guidelines Below.

1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

 Print Thread
Leaving my 1983 whaler outrage in the water
romd133
#1 Print Post
Posted on 10/12/17 - 3:19 AM
Member
Personal Page
Project Albums

Posts: 79
Comments: 3
Joined: 08/11/08

So I've had my 1983 25 foot outrage for about eight years and I have been trailering it and now I'm deciding to maybe leave it in the water my question is the Four Bilge areas that self drain is there a way to pump these areas out? I would appreciate someone that leaves their boat in the water to give me some advice on that thank you


Edited by romd133 on 10/16/17 - 6:42 AM
 
Pinion
#2 Print Post
Posted on 10/24/17 - 1:14 PM
Member

Posts: 18
Comments: 1
Joined: 05/19/13

Revenges had a bilge pump at the rear on starboard and I think the Outrages had it as an option. I dont know if the wiring is already there for Outrages, but I believe the wires are brown and purple for bilge pumps.

Since your boat has lived its life on a trailer, but if you are considering leaving it in the water for extended periods of time, you need to have it barrier coated and bottom painted. The gelcoat and fiberglass will not hold up without it.


 
chicaneries
#3 Print Post
Posted on 11/01/17 - 9:15 PM
Member

Posts: 45
Comments: 0
Joined: 10/09/13

I often read about the ill effects of leaving a Boston Whaler in the water without a barrier coat, My 1991, 17' Montauk has spent its entire seasonal life, May 1 through October 31, either on a mooting or slip in Cape Cod waters. The boat is bottom painted, the only growth or negative issue I've ever experienced is barnaclles on the transom saver block for my transducer, and a slight scum line from the stern towards the bow that starts at approximately a half inch wide and tapers to nothing. This line is easlily removed with a sponge and saltwater, this wouldn't even occur but I've never liked the way bottom paint looked on the side of a boat, my bottom paint is only applied to the bottom and extends vertically at the transom to meet the directional change of the hull. The boat does not appear to have taken on any water weight, and the gel coat still shines like a new penny with only minimal attention. I may be missing something but for a boat approaching her 30th birthday, it's holding up pretty well.


Edited by chicaneries on 11/01/17 - 9:33 PM
 
butchdavis
#4 Print Post
Posted on 11/02/17 - 6:34 AM
Member

Posts: 822
Comments: 0
Joined: 11/22/11

Barrier coat is inexpensive insurance and much cheaper/easier to apply than treating osmotic damage to your hull.

Of course some folks who did not apply barrier coat have not had a problem but many folks have had problems, thus Boston Whalers recommendation.


Butch
 
chicaneries
#5 Print Post
Posted on 11/04/17 - 1:38 AM
Member

Posts: 45
Comments: 0
Joined: 10/09/13

Be sure to know the moisture content of the area you plan to barrier coat, prior to application, as you will create far more problems, vs solved, without this information. Only a properly calibrated moisture meter or a laminate profile will provide the necessary information.

 
Jump to Forum:
Bookmark and Share
Today's Date & Time
March 29, 2024 - 1:49 AM
Users Online
Welcome
93SL16MN
as the newest member

· Guests Online: 10
· Members Online: 0
· Total Members: 49,964
Login
Username

Password

Remember Me


Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.
Top 5 Models Posted
· Montauk 17 1,622
· Sport 13 1,354
· Outrage 18 549
· Nauset 16 396
· Sport 15 363

View all Models Here
Render time: 0.16 seconds Copyright WhalerCentral.com © 2003-2024 82,706,994 unique visits